International Journal of Nanoscience and Nanotechnology

International Journal of Nanoscience and Nanotechnology

Effect of TiO2-MWCNTs Nanocomposite on the Performance of Mixed Matrix Nanofiltration Membranes: Manganese Ion Removal

Document Type : Research Paper

Authors
Sedigheh Daroumi 1
Ramin Yavari 2
Mohammad Ali Aroon 3
Takeshi Matsuura 4
1 University of Tehran, Tehran, Iran
2 Nuclear Fuel Cycle School, Nuclear science and technology Research institute, (NSTRI), P.O.Box. 11365-8486, Tehran, Iran
3 School of Chemical Engineering, College of Engineering, University of Tehran,Tehran, Iran
4 Industrial Membrane Research Laboratory, Chemical Engineering Department, University of Ottawa, Ottawa, Canada
10.22034/ijnn.2025.2024498.2490
Abstract
This study aims to investigate the removal of manganese ions from aqueous residues of the chemical industries using neat and mixed matrix polyethersulfone (PES) membranes. Functionalized multi-walled carbon nanotubes (MWCNTs), titanium dioxide nanoparticles (TiO2), and multi-walled carbon nanotubes/titanium dioxide nanoparticles (TiO2-functionalized MWCNTs hybrid) were used as the fillers in the mixed matrix membranes to improve the membrane performance. MWCNTs were oxidized and functionalized using nitric acid. TiO2 and TiO2-functionalized MWCNTs nanoparticles were synthesized by the sol-gel method and Sun et al.’s method, respectively. These nanoparticles were characterized by transmission electron microscopy (TEM) and nitrogen adsorption/desorption isotherms (BET). Both neat and mixed matrix PES membranes were fabricated by the phase inversion method and characterized by SEM and contact angle measurement. They were further subjected to the filtration test for manganese removal. SEM images showed that all the tested membranes have an asymmetric structure with a top-dense control layer supported by a sublayer with finger-like pores. Results of the contact angle test demonstrated adding each of these particles (functionalized MWCNTs, TiO2, and TiO2-functionalized MWCNTs) reduced the contact angle and, thus, increased the hydrophilicity of the membrane. The results of the filtration tests are as follows; Adding 0.1% functionalized MWCNTs could increase the membrane flux to 28.65 L/m2s (with 89.3% manganese ions rejection), adding 0.1% TiO2 increased the manganese ion rejection percentage to 92.06% (with a flux of 8.97 L/m2s) and adding 0.1% TiO2-functionalized MWCNTs hybrid increased the flux to 26 L/m2s (with 87.04% manganese ions rejection).
Keywords
Manganese
Nanofiltration
MWCNTs
TiO2
TiO2-MWCNTs hybrid
Wastewater treatment

Subjects

  1. REFERENCES       

    1. Patnaik, P., Pradyot, P., "Handbook of inorganic chemicals", Ebook, (2002) 1–1125, Retrieved from ftp://pvictor.homeftp.net/public/Sci_Library/Chem Library/Handbooks/Patnaik P. Handbook of inorganic chemicals (MGH, 2003)(T)(1125s).pdf
    2. Rahman, R. O., Ibrahium, H. A., Hung, Y-T, "Liquid radioactive wastes treatment: a review", Water, 3 (2011) 551–565. https://doi.org/10.3390/w3020551
    3. Lepel, E. A., Pratt, S. L., Robertson, D. E., Thomas, C. W., Haggard, D. L., "Radiological characterization of spent control rod assemblies", Journal of Radioanalytical and Nuclear Chemistry, 194(1) (1995) :81–94. https://doi.org/10.1007/BF02037615
    4. Gerber, G. B., Leonard, A., Hantson, P., "Carcinogenicity, mutagenicity and teratogenicity of manganese compounds", Critical Reviews in Oncology/Hematology, 42(1) (2002) 25–34.
    5. Crossgrove, J., Zheng, W., "Manganese toxicity upon overexposure", NMR in Biomedicine, 17(8) (2004) 544–553. https://doi.org/10.1002/nbm.931
    6. Zhang, W., Cheng, C. Y., "Manganese metallurgy review. Part II: Manganese separation and recovery from solution", Hydrometallurgy, 89(3) (2007) 160–177. https://doi.org/10.1016/j.hydromet.2007.08.009
    7. Zhang, W., Cheng, C. Y., Pranolo, Y., "Investigation of methods for removal and recovery of manganese in hydrometallurgical processes", Hydrometallurgy, 101(1) (2010) 58–63. https://doi.org/10.1016/j.hydromet.2009.11.018
    8. Pakarinen, J., Paatero, E., "Recovery of manganese from iron containing sulfate solutions by precipitation", Minerals Engineering, 24(3) (2011) 1421–1429. https://doi.org/10.1016/j.mineng.2011.06.004
    9. White, D. A., Asfar-Siddique, A., "Removal of manganese and iron from drinking water using hydrous manganese dioxide", Solvent extraction and ion exchange, 15(6) (1997) 1133–1145. https://doi.org/10.1080/07366299708934526
    10. Rumsby, P., Clegg, H., Jonsson, J., Benson, V., Harman, M., Doyle, T., Rushton, L., Wilkinson, D., Warick, P., "Speciation of Manganese in Drinking Water", EPA., 229 (2014) 120. http://dx.doi.org/10.1016/j.toxlet.2014.06.431
    11. Fu, F., Wang, Q., "Removal of heavy metal ions from wastewaters: a review", Journal of environmental management, 92 (3) (2011) 407–418. https://doi.org/10.1016/j.jenvman.2010.11.011
    12. Woodard, F., "Industrial waste treatment handbook", (2001) 264-318.
    13. Nonaka, T., Egawa, H., "Removal of Heavy Metals from Aqueous Solution by Poly(methacrylohydrazide)", Nippon Kagaku Kaishi, 1977(11) (1977) 1722–1727. https://doi.org/10.1246/nikkashi.1977.1722
    14. Bodzek, M., Konieczny, K., Kwiecińska, A., Taylor, P., Bodzek, M., Konieczny, K., Kwieci, A., "Application of membrane processes in drinking water treatment–state of art", Desalination and Water Treatment, 35(1-3) (2011) 164–184.
    15. Chaturvedi, S., Dave, P. N., "Removal of iron for safe drinking water", Desalination, 303 (2012) 1–11. https://doi.org/10.1016/j.desal.2012.07.003
    16. Mondal, S., Hsiao, C., S, R. W., "Nanofiltration/reverse osmosis for treatment of coproduced waters", Environmental Progress, 27(2) (2008) 173–179. https://doi.org/10.1002/ep
    17. Forests M of E, "Global good practices in industrial wastewater treatment and disposal / reuse , with special reference to common effluent treatment plants Central Pollution Control Board", (2014) 20-22
    18. Van-Der-Bruggen, B., "Chemical modification of polyethersulfone nanofiltration membranes: a review", Journal of Applied Polymer Science, 114(1) (2009) 630–642. https://doi.org/10.1002/app
    19. Wu, G., Gan, S., Cui, L., Xu, Y., "Preparation and characterization of PES/TiO 2 composite membranes", Applied Surface Science, 254(21) (2008) 7080–7086. https://doi.org/10.1016/j.apsusc.2008.05.221
    20. Ahmad, A. L., Abdulkarim, A. A., Ooi, B. S., Ismail, S., "Recent development in additives modifications of polyethersulfone membrane for flux enhancement", Chemical Engineering Journal, 223 (2013) 246–267. https://doi.org/10.1016/j.cej.2013.02.130
    21. Aroon, M. A., Ismail, A. F., Matsuura, T., Montazer-Rahmati, M. M., "Performance studies of mixed matrix membranes for gas separation: A review", Separation and Purification Technology, 75(3) (2010) 229–242. https://doi.org/10.1016/j.seppur.2010.08.023
    22. Madanirad, Z., Akbari, M., Shariaty-Niassar, M., Abadi, K. A. V., "Effects of Graphene Oxide Size on PES Ultrafiltration Hydrophilicity and Pure Water Flux", International Journal of Nanoscience and Nanotechnology, 19(2) (2023) 121–134. https://doi.org/10.22034/ijnn.2023.2001625.2372
    23. Celik, E., Park, H., Choi, H., Choi, H., "Carbon nanotube blended polyethersulfone membranes for fouling control in water treatment", Water Research, 45(1) (2011) 274–282. https://doi.org/10.1016/j.watres.2010.07.060
    24. Daraei, P., Madaeni, S. S., Ghaemi, N., Salehi, E., Khadivi, M. A., Moradian, R., Astinchap, B., "Novel polyethersulfone nanocomposite membrane prepared by PANI/Fe3O4 nanoparticles with enhanced performance for Cu (II) removal from water", Journal of Membrane Science, 415 (2012) 250–259. https://doi.org/10.1016/j.memsci.2012.05.007
    25. Rahimpour, A., Jahanshahi, M., Khalili, S., Mollahosseini, A., Zirepour, A., Rajaeian, B., "Novel functionalized carbon nanotubes for improving the surface properties and performance of polyethersulfone (PES) membrane". Desalination, 286 (2012) 99–107. https://doi.org/10.1016/j.desal.2011.10.039
    26. Shawky, H. A., Chae, S. R., Lin, S., Wiesner, M. R., "Synthesis and characterization of a carbon nanotube/polymer nanocomposite membrane for water treatment", Desalination, 272(1-3) (2011) 46–50. https://doi.org/10.1016/j.desal.2010.12.051
    27. Qiu, S., Wu, L., Pan, X., Zhang, L., Chen, H., Gao, C. "Preparation and properties of functionalized carbon nanotube/PSF blend ultrafiltration membranes", Journal of Membrane Science, 342(1-2) (2009) 165–172. https://doi.org/10.1016/j.memsci.2009.06.041
    28. Choi, J. H., Jegal, J., Kim, W. N., "Fabrication and characterization of multi-walled carbon nanotubes/polymer blend membranes", Journal of Membrane Science, 284(1-2) (2006) 406–415. https://doi.org/10.1016/j.memsci.2006.08.013
    29. Lehman, J. H., Terrones, M., Mansfield, E., Hurst, K. E., Meunier, V., "Evaluating the characteristics of multiwall carbon nanotubes", Carbon, 49(8) (2011) 2581–2602. https://doi.org/10.1016/j.carbon.2011.03.028
    30. Mansourpanah, Y., Madaeni, S. S., Rahimpour, A., Adeli, M., Hashemi, M. Y., Moradian, M. R., "Fabrication new PES-based mixed matrix nanocomposite membranes using polycaprolactone modified carbon nanotubes as the additive: Property changes and morphological studies", Desalination, 277(1-3) (2011) 171–177. https://doi.org/10.1016/j.desal.2011.04.022
    31. Pourfayaz, F., Boroun, S., Babaei, J., Ebrahimi Hoseinzadeh, B., "An Evaluation of the Adsorption Potential of MWCNTs for Benzene and Toluene Removal", International Journal of Nanoscience and Nanotechnology, 10(1) (2014) 27–34.
    32. Gui, M. M., Yap, Y. X., Chai, S.-P., Mohamed, A. R., "Multi-walled carbon nanotubes modified with (3-aminopropyl)triethoxysilane for effective carbon dioxide adsorption", International Journal of Greenhouse Gas Control, 14 (2013) 65–73. https://doi.org/https://doi.org/10.1016/j.ijggc.2013.01.004
    33. Vajtai, R., "Springer handbook of nanomaterials".Springer Handbook of Nanomaterials, (2013) 147-187 https://doi.org/10.1007/978-3-642-20595-88
    34. Hu, C., Liu, H., Zhang, Y., Zhang, M., Yu, J., Liu, X., Zhang, X., "Tuning microwave absorption properties of multi-walled carbon nanotubes by surface functional groups", Journal of Materials Science, 54 (2019) 2417–2426. https://doi.org/10.1007/s10853-018-2895-y
    35. Mohammadi, H., Hafezi, M., Hesaraki, S., Sepantafar, M. M., "Preparation and characterization of Sr-Ti-hardystonite (Sr-Ti-HT) nanocomposite for bone repair application", Nanomed. J., 2 (2015) 203–210. https://doi.org/10.7508/nmj
    36. Aroon, M. A., Beheshti, H., Barzin, J., Shariaty-Niassar, M., "Purified and functionalized MWCNTs: Application in CO2/CH4 separation using mixed matrix membranes", International Journal of Nanoscience and Nanotechnology, 14(4) (2018) 251–266.
    37. Yavari, R., Davarkhah, R., "Application of modified multiwall carbon nanotubes as a sorbent for zirconium (IV) adsorption from aqueous solution", Journal of Radioanalytical and Nuclear Chemistry, 298(2) (2013) 835–845. https://doi.org/10.1007/s10967-013-2476-0
    38. Peydayesh, M., Mohammadi, T., Bakhtiari, O., "Water desalination via novel positively charged hybrid nanofiltration membranes filled with hyperbranched polyethyleneimine modified MWCNT". Journal of Industrial and Engineering Chemistry, 69 (2019) 127–140. https://doi.org/10.1016/j.jiec.2018.09.007
    39. Peydayesh, M., Mohammadi, T., Bakhtiari, O., "Effective treatment of dye wastewater via positively charged TETA-MWCNT/PES hybrid nanofiltration membranes", Separation and Purification Technology, 194 (2018), 488–502. https://doi.org/10.1016/j.seppur.2017.11.070
    40. Peydayesh, M., Mohammadi, T., Nikouzad, S. K., "A positively charged composite loose nanofiltration membrane for water purification from heavy metals", Journal of Membrane Science, 611 (2020) 118205. https://doi.org/10.1016/j.memsci.2020.118205
    41. Guo, Y. S., Mi, Y. F., Zhao, F. Y., Ji, Y. L., An, Q. F., Gao, C. J., "Zwitterions functionalized multi-walled carbon nanotubes/polyamide hybrid nanofiltration membranes for monovalent/divalent salts separation", Separation and Purification Technology, 206 (2018) 59–68. https://doi.org/10.1016/j.seppur.2018.05.048
    42. Ismail, A. F., Goh, P. S., Sanip, S. M., Aziz, M., "Transport and separation properties of carbon nanotube-mixed matrix membrane". Separation and Purification Technology, 70(1) (2009), 12–26.
    43. Aroon, M. A., Ismail, A. F., Montazer-Rahmati, M. M., Matsuura, T., "Effect of chitosan as a functionalization agent on the performance and separation properties of polyimide/multi-walled carbon nanotubes mixed matrix flat sheet membranes", Journal of Membrane Science, 364(1) (2010) 309–317. https://doi.org/https://doi.org/10.1016/j.memsci.2010.08.023
    44. Aroon, M. A., Ismail, A. F., Matsuura, T., "Beta-cyclodextrin functionalized MWCNT: A potential nano-membrane material for mixed matrix gas separation membranes development", Separation and Purification Technology, 115 (2013) 39–50. https://doi.org/https://doi.org/10.1016/j.seppur.2013.04.025
    45. Balasubramanian, K., Burghard, M., "Chemically functionalized carbon nanotubes", Small, 1 (2005) 180–192. https://doi.org/10.1002/smll.200400118
    46. Marjani, A., Taghvaie Nakhjiri, A., Adimi, M., Fathinejad Jirandehi, H., Shirazian, S., "Modification of polyethersulfone membrane using MWCNT-NH2 nanoparticles and its application in the separation of azeotropic solutions by means of pervaporation", PLOS ONE, 15(7) (2020) e0236529. https://doi.org/10.1371/journal.pone.0236529
    47. Vatanpour, V., Madaeni, S. S., Moradian, R., Zinadini, S., Astinchap, B., "Fabrication and characterization of novel antifouling nanofiltration membrane prepared from oxidized multiwalled carbon nanotube/polyethersulfone nanocomposite", Journal of Membrane Science, 375(1-2) (2011) 284–294. https://doi.org/10.1016/j.memsci.2011.03.055
    48. Shamspur, T., & Mostafavi, A., "Application of modified multiwalled carbon nanotubes as a sorbent for simultaneous separation and preconcentration trace amounts of Au(III) and Mn(II)", Journal of Hazardous Materials, 168(2-3) (2009) 1548–1553. https://doi.org/10.1016/j.jhazmat.2009.03.028
    49. Zhu, Y., Zhang, L., Gao, C., Cao, L., "The synthesis of nanosized TiO2 powder using a sol-gel method with TiCl4 as a precursor", Journal of Materials Science, 35(16) (2000) 4049–4054. https://doi.org/10.1023/A:1004882120249
    50. Zhang, Q., Gao, L., Guo, J., "Effect of hydrolysis conditions on morphology and crystallization of nanosized TiO2 powder", Journal of the European Ceramic Society, 20(12) (2000) 2153–2158. https://doi.org/10.1016/S0955-2219(00)00085-6
    51. Bet-moushoul, E., Mansourpanah, Y., Farhadi, K., Tabatabaei, M., "TiO 2 nanocomposite based polymeric membranes : A review on performance improvement for various applications in chemical engineering processes", CHEMICAL ENGINEERING JOURNAL, 283 (2016) 29–46. https://doi.org/10.1016/j.cej.2015.06.124
    52. Sotto, A., Boromand, A., Zhang, R., Luis, P., Arsuaga, J. M., Kim, J., Van-der-Bruggen, B., "Effect of nanoparticle aggregation at low concentrations of TiO2 on the hydrophilicity, morphology, and fouling resistance of PES–TiO2 membranes", Journal of colloid and interface science, 363(2) (2011) 540–550. https://doi.org/10.1016/j.jcis.2011.07.089
    53. Yang, Y., Zhang, H., Wang, P., Zheng, Q., Li, J., "The influence of nano-sized TiO 2 fillers on the morphologies and properties of PSF UF membrane", 288 (2007) 231–238. https://doi.org/10.1016/j.memsci.2006.11.019
    54. Luo, M., Tang, W., Zhao, J., Pu, C., "Hydrophilic modification of poly ( ether sulfone ) used TiO 2 nanoparticles by a sol – gel process", 172 (2006), 431–436. https://doi.org/10.1016/j.jmatprotec.2005.11.004
    55. Lee, H. S., Im, S. J., Kim, J. H., Kim, H. J., Kim, J. P., Min, B. R., "Polyamide thin-film nanofiltration membranes containing TiO 2 nanoparticles", 219 (2008) 48–56. https://doi.org/10.1016/j.desal.2007.06.003
    56. Mansourpanah, Y., Madaeni, S. S., Rahimpour, A., Farhadian, A., Taheri, A. H., "Formation of appropriate sites on nanofiltration membrane surface for binding TiO 2 photo-catalyst : Performance , characterization and fouling-resistant capability", 330 (2009), 297–306. https://doi.org/10.1016/j.memsci.2009.01.001
    57. Bae, T.-H., Tak, T.-M., "Effect of TiO2 nanoparticles on fouling mitigation of ultrafiltration membranes for activated sludge filtration", Journal of Membrane Science, 249(1-2) (2005) 1–8. https://doi.org/10.1016/j.memsci.2004.09.008
    58. Ranjbaran, H., Ameri, E., Dehghani, B., "Preparation of dendrimer/TiO2 polysulfone nanofiltration membrane to improve antibacterial, antifouling and separation performance of contaminants (heavy metals, salts, dyes)", Polymer Bulletin, (2023) 1–16. https://doi.org/10.1007/s00289-023-04785-7
    59. Parvizian, F., Bandehali, S., Ansari, F., "Separation performance modification of PES-based nanofiltration membranes by oleic acid modified-TiO2 nanoparticles", Nashrieh Shimi va Mohandesi Shimi Iran, (2020) 1–2. Retrieved from https://www.nsmsi.ir/article_46353.html
    60. Kumar, S. A., Srinivasan, G., Govindaradjane, S., "A novel synergistic effect of TiO2 and ZnO incorporation in PES-based thin-film nanocomposite nanofiltration membrane for treatment of textile wastewater", Environmental Monitoring and Assessment, 194 (2022), 848. https://doi.org/10.1007/s10661-022-10525-7
    61. Zhu, L., Wu, M., Van der Bruggen, B., Lei, L., Zhu, L., "Effect of TiO2 content on the properties of polysulfone nanofiltration membranes modified with a layer of TiO2–graphene oxide", Separation and Purification Technology, 242 (2020) 116770. https://doi.org/10.1016/j.seppur.2020.116770
    62. Safarpour, M., Vatanpour, V., Khataee, A., "Preparation and characterization of graphene oxide/TiO2 blended PES nanofiltration membrane with improved antifouling and separation performance", Desalination, 393 (2016) 65–78. https://doi.org/10.1016/j.desal.2015.07.003
    63. Razmjou, A., Mansouri, J., Chen, V., "The effects of mechanical and chemical modification of TiO2nanoparticles on the surface chemistry, structure and fouling performance of PES ultrafiltration membranes", Journal of Membrane Science, 378(1-2) (2011) 73–84. https://doi.org/10.1016/j.memsci.2010.10.019
    64. Li, J. F., Xu, Z. L., Yang, H., Yu, L. Y., Liu, M., "Effect of TiO2nanoparticles on the surface morphology and performance of microporous PES membrane", Applied Surface Science, 255(9) (2009) 4725–4732. https://doi.org/10.1016/j.apsusc.2008.07.139
    65. Razmjou, A., Resosudarmo, A., Holmes, R. L., Li, H., Mansouri, J., Chen, V., "The effect of modified TiO2nanoparticles on the polyethersulfone ultrafiltration hollow fiber membranes", Desalination, 287 (2012) 271–280. https://doi.org/10.1016/j.desal.2011.11.025
    66. Sun, J., Gao, L., "Development of a dispersion process for carbon nanotubes in ceramic matrix by heterocoagulation", Carbon, 41(5) (2003) 1063–1068. https://doi.org/10.1016/S0008-6223(02)00441-4
    67. Tsumura, T., Kojitani, N., Izumi, I., Iwashita, N., Toyoda, M., Inagaki, M., "Carbon coating of anatase-type TiO2 and photoactivity", Journal of Materials Chemistry, 12(5) (2002) 1391–1396. https://doi.org/10.1039/b201942f
    68. Safi, M. A., Ghozatloo, A., Hamidi, A. A., "Calculation of Heat Transfer Coefficient of MWCNT-TiO 2 Nanofluid in Plate Heat Exchanger", International Journal of Nanoscience, 10(3) (2014) 153–162.
    69. Jouyban, A., Fakhree, M. A. A., Shayanfar, A., "Review of pharmaceutical applications of N-methyl-2-pyrrolidone",Journal of Pharmacy and Pharmaceutical Sciences, 13(4) (2010) 524–535. https://doi.org/10.18433/j3p306
    70. Teodorescu, M., Bercea, M., "Poly(vinylpyrrolidone) – A Versatile Polymer for Biomedical and Beyond Medical Applications", Polymer - Plastics Technology and Engineering, 54(9) (2015) 923–943. https://doi.org/10.1080/03602559.2014.979506
    71. Liu, X., "Preparation and characterization of pure anatase nanocrystals by sol–gel method", Powder technology, 224 (2012) 287–290. https://doi.org/10.1016/j.powtec.2012.03.007
    72. Sun, J., Iwasa, M., Gao, L., Zhang, Q., "Single-walled carbon nanotubes coated with titania nanoparticles", Carbon, 4(42) (2004) 895–899.
    73. Khalfaoui, M., Knani, S., Hachicha, M. A., Lamine, A. Ben, "New theoretical expressions for the five adsorption type isotherms classified by BET based on statistical physics treatment", Journal of Colloid and Interface Science, 263 (2003) 350–356. https://doi.org/10.1016/S0021-9797(03)00139-5
    74. Houston TX, "BET Surface Area Analyzer", Seminar and Practical Training Short Course, 1(2006).
    75. Bakeri, G., Ismail, A. F., Shariaty-niassar, M., Matsuura, T., "Effect of polymer concentration on the structure and performance of polyetherimide hollow fiber membranes", Journal of Membrane Science, 363(1-2) (2010) 103–111. https://doi.org/10.1016/j.memsci.2010.07.018
    76. Soroko, I., Livingston, A., "Impact of TiO2 nanoparticles on morphology and performance of crosslinked polyimide organic solvent nanofiltration (OSN) membranes", Journal of Membrane Science, 343(1-2) (2009) 189–198. https://doi.org/10.1016/j.memsci.2009.07.026
    77. Li, X., Fang, X., Pang, R., Li, J., Sun, X., Shen, J.,Han, W., Wang, L., "Self-assembly of TiO2 nanoparticles around the pores of PES ultrafiltration membrane for mitigating organic fouling", Journal of Membrane Science, 467 (2014), 226–235. https://doi.org/10.1016/j.memsci.2014.05.036
    78. Marczenko, Z., Balcerzak, M., "Separation, Preconcentration and Spectrophotometry in Inorganic Analysis", Analytical Spectroscopy Library, 10 (2000) 253–261. https://doi.org/http://dx.doi.org/10.1016/S0926-4345(00)80093-0
    79. Sing, K. S. W., "Physisorption of gases by carbon blacks", Carbon, 32(7) (1994) 1311–1317. https://doi.org/https://doi.org/10.1016/0008-6223(94)90117-1
    80. Leddy, N., "surface area and porosity", CMA Analytical, 5 (2012) 23–64.
    81. Donohue, M. D., Aranovich, G. L., "Classification of Gibbs adsorption isotherms", Advances in Colloid and Interface Science, 76 (1998) 137–152. https://doi.org/10.1016/S0001-8686(98)00044-X
    82. Vatanpour, V., Madaeni, S. S., Moradian, R., Zinadini, S., Astinchap, B., "Novel antibifouling nanofiltration polyethersulfone membrane fabricated from embedding TiO2coated multiwalled carbon nanotubes", Separation and Purification Technology, 90 (2012) 69–82. https://doi.org/10.1016/j.seppur.2012.02.014
    83. Wu, H., Tang, B., Wu, P., "Novel ultrafiltration membranes prepared from a multi-walled carbon nanotubes / polymer composite", Journal of Membrane Science, 362(1-2) (2010) 374–383. https://doi.org/10.1016/j.memsci.2010.06.064
    84. Vatanpour, V., Esmaeili, M., Farahani, M. H. D. A., "Fouling reduction and retention increment of polyethersulfone nanofiltration membranes embedded by amine-functionalized multi-walled carbon nanotubes", Journal of Membrane Science, 466 (2014) 70–81. https://doi.org/10.1016/j.memsci.2014.04.031
    85. Rahimpour, A., Madaeni, S. S., Taheri, A. H., Mansourpanah, Y., "Coupling TiO2 nanoparticles with UV irradiation for modification of polyethersulfone ultrafiltration membranes", Journal of Membrane Science, 313(1-2) (2008) 158–169. https://doi.org/10.1016/j.memsci.2007.12.075
    86. Mohammad, A. W., Othaman, R., Hilal, N., "Potential use of nanofiltration membranes in treatment of industrial wastewater from Ni-P electroless plating", Desalination, 168(1-3) (2004) 241–252. https://doi.org/10.1016/j.desal.2004.07.004
    87. Vatanpour, V., Madaeni, S. S., Khataee, A. R., Salehi, E., Zinadini, S., Monfared, H. A., "TiO2 embedded mixed matrix PES nanocomposite membranes: Influence of different sizes and types of nanoparticles on antifouling and performance", Desalination, 292 (2012), 19–29. https://doi.org/10.1016/j.desal.2012.02.006
International Journal of Nanoscience and Nanotechnology
Volume 20, Issue 4
2024
Pages 231-248